PEEK 150G (Glass-Filled) Polymer: Properties, Applications, and CNC Machining Guide

Selecting the right engineering material is the foundation of any successful CNC machining project. PEEK 150G is Glass-fiber-reinforced polyether ether ketone (PEEK), and it is specified across demanding industries because its property profile matches real service loads. In this guide we examine its chemical composition, mechanical and physical properties, where it is used in production, and the practical parameters our machinists apply when cutting, drilling and finishing it on modern CNC equipment. Whether you are specifying raw stock or validating a design, the data below will help you make a confident, cost-effective decision.

Understanding PEEK 150G also means understanding how it behaves once it leaves the saw and enters the spindle. The sections that follow move from metallurgy and chemistry to real machining advice, so you can plan tolerances, tooling and finishing in a single pass rather than discovering problems on the shop floor. For related processing topics, see our resources on Präzisions-CNC-Bearbeitung und material selection for turned parts.

We have machined PEEK 150G in quantities ranging from single prototypes to full production runs, and the guidance here reflects that hands-on experience. Numbers are representative of the common supplied temper; always confirm critical values against a mill certificate for the exact heat you receive.

Chemical Composition and Alloy Chemistry

PEEK 150G is Glass-fiber-reinforced polyether ether ketone (PEEK). Its performance comes from a carefully balanced chemistry in which each element plays a specific role: major alloying elements build strength and hardenability, while minor additions refine the grain, improve machinability or stabilize the microstructure during heat treatment. The typical composition is shown in the table below, and we then explain what the most important elements do.

In PEEK 150G, base (typically PEEK matrix): the base polymer delivers the high-temperature and chemical resistance this family is known for. Controlling this element within tight limits is what lets mills deliver repeatable, specification-grade stock.

In PEEK 150G, filler (typically Glass fiber (typically ~10-15%)): the filler raises stiffness, wear resistance or electrostatic performance as required. Controlling this element within tight limits is what lets mills deliver repeatable, specification-grade stock.

In PEEK 150G, grade (typically Semi-crystalline reinforced): the grade is tuned for the intended balance of stiffness, toughness and cost. Controlling this element within tight limits is what lets mills deliver repeatable, specification-grade stock.

In production the composition is verified by spectrometry and documented on the material certificate. Because small shifts change hardenability, corrosion behaviour and how the material responds to cutting tools, we always match the heat certificate to the process plan before the first bar is loaded.

Mechanische Eigenschaften

Mechanical properties define how PEEK 150G carries load, resists deformation and survives fatigue in service. The values quoted here are representative of the common supplied temper; heat treatment and section size will move the numbers, so confirm with your mill certificate for critical parts. The summary table is followed by notes on why each value matters to a designer.

The tensile and yield strengths tell you the load a feature can carry, while elongation reports how much ductility remains to absorb overload or accommodate forming. Hardness is a useful proxy for wear resistance and for predicting tool wear during machining. Together these figures let you size sections, choose safety factors and set inspection limits with confidence.

Because PEEK 150G is a polymer, the strength numbers describe behaviour at room temperature and change markedly with heat and strain rate. Treat them as a starting point and validate with molded or machined coupons under your actual service conditions, especially where creep or repeated impact is expected.

Physical and Thermal Properties

Physical properties affect machining strategy as much as mechanical ones. Density drives mass and handling, thermal conductivity governs how heat leaves the cut, and the melting or softening point sets the ceiling for cutting speed and the type of coolant you can use. The table below summarizes the key values for PEEK 150G.

These values explain why PEEK 150G machines the way it does. Low thermal conductivity, for example, traps heat at the tool edge and pushes you toward sharper tools, lower depths of cut and aggressive coolant delivery. A low or high density changes how you fixture and balance a part. High strength-to-weight ratios, on the other hand, are exactly why designers keep specifying this material even when a cheaper alternative exists.

Wesentliche Eigenschaften

PEEK 150G earns its place in engineering designs because of a short list of characteristics that matter on the shop floor and in the field. Each one is explained below so you can judge fit against your requirement.

Higher stiffness than unfilled PEEK

Higher stiffness than unfilled peek In the context of PEEK 150G, this matters because it influences both the performance of the finished part and the way the raw stock must be processed, heat treated and machined to release its full potential.

Better creep resistance

Better creep resistance In the context of PEEK 150G, this matters because it influences both the performance of the finished part and the way the raw stock must be processed, heat treated and machined to release its full potential.

Lower cost per part

Lower cost per part In the context of PEEK 150G, this matters because it influences both the performance of the finished part and the way the raw stock must be processed, heat treated and machined to release its full potential.

Retains PEEK’s chemical and thermal resistance

Retains peek’s chemical and thermal resistance In the context of PEEK 150G, this matters because it influences both the performance of the finished part and the way the raw stock must be processed, heat treated and machined to release its full potential.

Together these traits make PEEK 150G a practical choice where performance, weight and manufacturability must all be satisfied at once. None of them is unique on its own, but the combination is what separates a specification-grade material from a commodity one.

Industrielle und ingenieurtechnische Anwendungen

The real test of any material is where it is trusted in production. PEEK 150G appears across aerospace, automotive, energy and precision industries in the following roles, each chosen because the property profile matches the duty cycle:

Structural insulators

Rigid electrical and thermal parts.

When we produce structural insulators for this kind of application, we pay particular attention to the critical dimensions and surface condition, because that is what determines whether the part survives its service life. Our inspection reports document every key feature.

Pump and valve bodies

Chemical-resistant housings.

When we produce pump and valve bodies for this kind of application, we pay particular attention to the critical dimensions and surface condition, because that is what determines whether the part survives its service life. Our inspection reports document every key feature.

Aerospace clips

Stiff, lightweight mounts.

When we produce aerospace clips for this kind of application, we pay particular attention to the critical dimensions and surface condition, because that is what determines whether the part survives its service life. Our inspection reports document every key feature.

Semiconductor fixtures

Dimensional-stable holders.

When we produce semiconductor fixtures for this kind of application, we pay particular attention to the critical dimensions and surface condition, because that is what determines whether the part survives its service life. Our inspection reports document every key feature.

For background on how we hold and fixture such parts, review our notes on fixture design for CNC milling und tolerance stacking in assemblies. Good fixturing is often the difference between a part that holds tolerance and one that does not.

CNC Machining Guidelines

Machining PEEK 150G successfully is about matching tooling, speed and coolant to its specific behaviour. The recommendations below reflect shop-proven practice for holding dimension, surface finish and tool life, and they are a starting point that our programmers refine for each geometry.

Werkzeugauswahl

Diamond-coated or sharp carbide; glass is abrasive.

Beyond the grade, tool geometry matters: a high positive rake reduces cutting forces, a polished flute helps evacuate sticky chips, and a rigid tool holder limits vibration that would otherwise ruin surface finish. We select geometry per operation rather than using one general-purpose end mill.

Schnittparameter

Milling 180-350 m/min, turning 80-200 m/min.

These ranges assume a rigid machine and a well-clamped part. If chatter appears, the first response is to shorten tool overhang and increase spindle speed into a stable lobe, not simply to slow the feed. Our shops log proven parameters per material so repeat jobs start from a known-good point.

Tolerances and Surface Finish

Hold +/-0.02 mm; anneal to stabilize dimensions.

Workholding and Fixturing

Stable workholding is the quiet hero of precision machining. For PEEK 150G we favour full-contact soft jaws, vacuum or dedicated fixtures that constrain the part without distorting it, then measure the first piece before releasing the batch. This discipline is what lets us hold the tight tolerances the application demands.

Common challenges when cutting PEEK 150G: Abrasive fibers wear tools; use diamond coating, sharp edges, coolant, low depth.. A rigid setup, sharp edges and consistent coolant delivery resolve most of them, and our quality team verifies every critical dimension before shipment so the part that reaches your dock is the part on the drawing.

Heat Treatment and Surface Finishing

Anneal near 150 C after roughing to relieve stress.

After thermal treatment, PEEK 150G is usually finished by grinding, honing or light CNC cleanup to reach the final tolerance, because hardened material is too hard to cut economically. Surface treatments such as anodizing, plating, nitriding, black oxide or coating can then be added when wear, corrosion or appearance call for it. We coordinate heat treatment and finishing with machining so distortion is planned for, not discovered late.

How PEEK 150G Compares with Similar Materials

No material is chosen in isolation. The table below positions PEEK 150G against nearby alternatives so you can see where it wins and where a substitute might be better. The right choice is almost always a trade-off between cost, weight, strength and how easily the part can be made.

If your priority is the lowest possible weight, the highest strength, or the easiest machining, the right neighbour in this table may tip the decision. Our engineers can run a quick trade study with your loads and volumes, and often a small change in alloy or temper removes an expensive secondary operation.

Tuofa CNC Germany: Your Precision Manufacturing Partner

When your design is ready, Tuofa CNC Deutschland turns materials like PEEK 150G into finished, inspected components. We are a precision CNC machining supplier serving automotive, aerospace, medical and industrial customers who need consistent quality and short lead times, and we treat every order as a partnership rather than a transaction.

Why Engineers Choose Tuofa CNC Germany

We combine ISO-controlled processes, experienced programmers and a transparent quoting workflow, so you always know what you will receive before we cut the first chip. From a single prototype to full production, the same quality system applies, which removes the risk that prototype and production parts behave differently.

Our CNC Capabilities

Our workshop runs 3-, 4- and 5-axis CNC milling centers, CNC turning lathes with live tooling, and support processes such as grinding, deburring and inspection. We routinely hold tight tolerances on metals, plastics and specialty alloys like PEEK 150G, and our CAD/CAM team optimizes toolpaths for both cycle time and surface quality.

Materials and Tolerances We Handle

Beyond PEEK 150G, we machine aluminum, stainless and alloy steels, titanium, copper alloys, PEEK and other engineering polymers. Typical tolerances reach +/-0.01 mm on critical features, with full material traceability and first-article inspection on request. Get a quote through our CNC-Bearbeitungsdienste page, or send us your drawing for a fast, detailed response.

Fazit

PEEK 150G is Glass-fiber-reinforced polyether ether ketone (PEEK), valued for its balanced combination of properties and proven track record in demanding applications. With the right composition, heat treatment and CNC parameters, it delivers reliable, repeatable parts that hold up in the field. Tuofa CNC Germany is ready to machine it to your drawing and tolerance, with the inspection and traceability your program requires. Reach out today to discuss your project and receive a fast, detailed quotation.