PA6 Mineral40 typically exhibits a tensile strength in the range of 60-80 MPa and a tensile modulus between 5.0 and 6.5 GPa. The flexural modulus is similarly elevated, often reaching 4.5-6.0 GPa. This stiffness is approximately double that of unfilled PA6, allowing for thinner wall sections in component design without sacrificing rigidity. However, the elongation at break is significantly reduced, typically falling between 2% and 5%, which means the material is less ductile and more prone to brittle failure under impact loads compared to unfilled nylon.
Chemische samenstelling en materiaalstructuur
Impact strength is one area where PA6 Mineral40 shows limitations. The Izod notched impact strength typically ranges from 3 to 5 kJ/m², which is considerably lower than unfilled PA6 (often 5-10 kJ/m²). This reduced toughness must be considered in applications subject to dynamic loading or potential impact events. Conversely, the creep resistance of PA6 Mineral40 is substantially improved over unfilled grades. Under sustained loads, the mineral fillers prevent polymer chain slippage, reducing time-dependent deformation. This makes the material suitable for spring clips, brackets, and other components that must maintain clamping force over extended periods.
Role of Mineral Fillers in PA6
The mineral fillers in PA6 Mineral40 serve multiple critical functions. Unlike glass fibers that provide directional reinforcement, mineral particles are more equiaxed in shape, which results in more uniform mechanical properties across all directions. This isotropic behavior is particularly valuable for components that experience multi-axial loading. The fillers also increase the material’s stiffness, reduce its coefficient of thermal expansion, and improve its creep resistance compared to unfilled PA6. Additionally, mineral fillers act as nucleating agents, promoting faster crystallization during cooling and reducing cycle times in injection molding.
Comparison with Glass-Fiber-Reinforced PA6
While PA6 GF30 (30% glass fiber) offers higher tensile strength and stiffness, PA6 Mineral40 provides distinct advantages in certain applications. The mineral-filled grade exhibits significantly less warpage and shrinkage, produces smoother surface finishes, and is easier to machine due to reduced abrasive wear on cutting tools. However, it cannot match the load-bearing capacity of glass-reinforced grades. This trade-off is important for design engineers when selecting between these material families.
| Property | PA6 Mineral40 (Typical) | PA6 Unfilled (Typical) | PA6 GF30 (Typical) |
|---|---|---|---|
| Dichtheid (g/cm³) | 1.45 – 1.50 | 1.13 – 1.15 | 1.35 – 1.40 |
| Treksterkte (MPa) | 60 – 80 | 60 – 85 | 150 – 190 |
| Trekmodulus (GPa) | 5.0 – 6.5 | 2,5 – 3,5 | 8.5 – 11.0 |
| Rek bij breuk (%) | 2 – 5 | 20 – 60 | 3 – 5 |
| Warmtevervormingstemperatuur (°C bij 1,8 MPa) | 120 – 150 | 65 – 80 | 200 – 215 |
Table 1: Comparative properties of PA6 grades. Values are typical ranges, not guaranteed specifications.
Mechanical Properties of PA6 Mineral40
Het mechanische gedrag van PA6 Mineral40 wordt gekenmerkt door een hoge stijfheid, goede druksterkte en uitstekende dimensionele stabiliteit. Deze eigenschappen maken het geschikt voor structurele componenten die nauwkeurige toleranties vereisen en bestand moeten zijn tegen vervorming onder belasting.
Trek- en buigprestaties
PA6 Mineral40 typically exhibits a tensile strength in the range of 60-80 MPa and a tensile modulus between 5.0 and 6.5 GPa. The flexural modulus is similarly elevated, often reaching 4.5-6.0 GPa. This stiffness is approximately double that of unfilled PA6, allowing for thinner wall sections in component design without sacrificing rigidity. However, the elongation at break is significantly reduced, typically falling between 2% and 5%, which means the material is less ductile and more prone to brittle failure under impact loads compared to unfilled nylon.
Slagvastheid en kruipgedrag
Impactsterkte is een gebied waarin PA6 Mineral40 beperkingen vertoont. De Izod-notch impactsterkte ligt doorgaans tussen 3 en 5 kJ/m², wat aanzienlijk lager is dan bij onversterkt PA6 (vaak 5-10 kJ/m²). Deze verminderde taaiheid moet worden overwogen bij toepassingen die onderhevig zijn aan dynamische belastingen of mogelijke impactgebeurtenissen. Anderzijds is de kruipweerstand van PA6 Mineral40 aanzienlijk verbeterd ten opzichte van onversterkte grades. Onder langdurige belasting voorkomen de minerale vulstoffen het wegglijden van polymeerketens, waardoor tijdafhankelijke vervorming wordt verminderd. Dit maakt het materiaal geschikt voor veerklemmen, beugels en andere componenten die gedurende lange periodes de klemkracht moeten behouden.
Fysische en thermische eigenschappen
PA6 Mineral40 has inherent flammability characteristics typical of unreinforced polyamides, with a UL94 HB rating in its natural state. For applications requiring flame retardancy, halogen-free flame-retardant versions of mineral-filled PA6 are available. The arc resistance of the material is generally good, though mineral fillers can sometimes reduce arc resistance compared to unfilled polymers. For demanding electrical applications, it is advisable to consult the specific datasheet of the chosen grade and conduct appropriate testing.
Density and Water Absorption
PA6 Mineral40 offers a distinctive combination of properties that make it the material of choice for numerous industrial applications. Understanding these advantages helps engineers select the right material for their specific requirements.
Thermal Stability and Heat Deflection
One of the most significant advantages of PA6 Mineral40 over glass-reinforced grades is its exceptional dimensional stability. The mineral fillers reduce mold shrinkage from approximately 1.5-2.0% (unfilled PA6) to 0.4-0.8%, and the isotropic nature of the fillers minimizes differential shrinkage that causes warpage. This makes PA6 Mineral40 ideal for large, flat components, precision housings, and parts with tight tolerance requirements. Components machined from PA6 Mineral40 stock also maintain their dimensions better than unfilled nylon when exposed to moisture or temperature changes.
| Fysische eigenschap | PA6 Mineral40 (Typical) | Testmethode |
|---|---|---|
| Dichtheid (g/cm³) | 1.45 – 1.50 | ISO 1183 |
| Water Absorption at Saturation (23°C, 50% RH) | 1.5 – 2.0% | ISO 62 |
| Smeltpunt (°C) | 220 – 225 | ISO 11357 |
| Warmtegeleidingsvermogen (W/m·K) | 0,35 – 0,45 | ISO 22007 |
| Volume Resistivity (Ω·cm) | 10¹² – 10¹⁴ | IEC 60093 |
| Oppervlakteweerstand (Ω) | 10¹⁰ – 10¹² | IEC 60093 |
Table 2: Physical properties of PA6 Mineral40. Values are typical ranges, not guaranteed specifications.
Electrical Properties and Insulation Characteristics
PA6 Mineral40 exhibits good electrical insulation properties, though the mineral fillers can influence dielectric behavior compared to unfilled nylon. These characteristics are relevant for electrical housings, connectors, and insulating components.
Dielectric Strength and Tracking Resistance
The dielectric strength of PA6 Mineral40 typically ranges from 20 to 30 kV/mm, depending on thickness and moisture content. The Comparative Tracking Index (CTI) is an important parameter for electrical applications, and mineral-filled PA6 grades often achieve CTI values of 400-600V, making them suitable for use in higher-voltage environments. However, it is essential to note that moisture absorption can degrade electrical properties, so components intended for humid environments may require protective coatings or design adjustments.
Arc Resistance and Flammability
PA6 Mineral40 bezit inherente brandbaarheidskenmerken die typerend zijn voor onversterkte polyamiden, met een UL94 HB-classificatie in zijn natuurlijke staat. Voor toepassingen die vlamvertragendheid vereisen, zijn halogeenvrije vlamvertragende versies van mineralversterkt PA6 beschikbaar. De boogbestendigheid van het materiaal is over het algemeen goed, hoewel minerale vulstoffen de boogbestendigheid soms kunnen verlagen in vergelijking met onversterkte polymeren. Voor veeleisende elektrische toepassingen is het raadzaam de specifieke datasheet van de gekozen grade te raadplegen en passende tests uit te voeren.
Belangrijkste kenmerken en voordelen
PA6 Mineral40 biedt een unieke combinatie van eigenschappen die het tot de favoriete keuze maken voor talrijke industriële toepassingen. Het begrijpen van deze voordelen helpt ingenieurs om het juiste materiaal te selecteren voor hun specifieke eisen.
Dimensionale stabiliteit en geringe kromming
One of the most significant advantages of PA6 Mineral40 over glass-reinforced grades is its exceptional dimensional stability. The mineral fillers reduce mold shrinkage from approximately 1.5-2.0% (unfilled PA6) to 0.4-0.8%, and the isotropic nature of the fillers minimizes differential shrinkage that causes warpage. This makes PA6 Mineral40 ideal for large, flat components, precision housings, and parts with tight tolerance requirements. Components machined from PA6 Mineral40 stock also maintain their dimensions better than unfilled nylon when exposed to moisture or temperature changes.
Oppervlakteafwerking en esthetiek
Beyond automotive and electrical uses, PA6 Mineral40 finds application in industrial machinery components such as gears, pulleys, housings, and wear pads. Its low friction coefficient and good wear resistance make it suitable for sliding components. In consumer products, the material is used in power tool housings, appliance components, and sporting goods. The material’s ability to be machined to tight tolerances makes it a preferred choice for prototyping and low-volume production of custom components, including specialized items like
Cost-Effectiveness and Processability
Engine covers, fan shrouds, oil pans, brackets
Applications of PA6 Mineral40
Connectors, coil formers, switch components
Automotive Industry Applications
Prototypes, custom parts, precision components mounting blocks used in vibration isolation systems.
Electrical and Electronic Applications
Table 3: Application sectors for PA6 Mineral40. terminal blocks, PA6 Mineral40 offers the necessary combination of electrical insulation and mechanical strength.
Industriële en consumententoepassingen
Beyond automotive and electrical uses, PA6 Mineral40 finds application in industrial machinery components such as gears, pulleys, housings, and wear pads. Its low friction coefficient and good wear resistance make it suitable for sliding components. In consumer products, the material is used in power tool housings, appliance components, and sporting goods. The material’s ability to be machined to tight tolerances makes it a preferred choice for prototyping and low-volume production of custom components, including specialized items like CNC machined shift knobs in automotive aftermarket applications.
| Industry | Typische toepassingen | Belangrijkste gebruikte eigenschap |
|---|---|---|
| Automotive | Engine covers, fan shrouds, oil pans, brackets | Heat resistance, dimensional stability |
| Elektrische geleidbaarheid | Connectoren, spoelformers, schakelcomponenten | Dielectric strength, tracking resistance |
| Industrieel | Gears, pulleys, housings, wear pads | Stiffness, wear resistance |
| Consument | Power tool housings, appliance parts | Surface finish, impact resistance |
| Bewerken | Prototypes, maatwerkonderdelen, precisiecomponenten | Machinability, dimensional stability |
Table 3: Application sectors for PA6 Mineral40.
CNC Machining of PA6 Mineral40
PA6 Mineral40 is an excellent candidate for CNC machining, offering good machinability relative to glass-reinforced alternatives. However, its unique properties require specific machining strategies to achieve optimal results and avoid common pitfalls.
Aanbevolen snijparameters
When machining PA6 Mineral40, carbide tooling is recommended due to the abrasive nature of the mineral fillers. For milling operations, cutting speeds of 150-300 m/min with feed rates of 0.1-0.3 mm/tooth are typical starting points. The material is less abrasive than glass-filled nylon, allowing for longer tool life, but still harder than unfilled PA6. Climb milling is preferred to reduce heat generation and improve surface finish. For drilling operations, standard twist drills with a 118° point angle work well, though peck drilling is recommended for deep holes to evacuate chips and prevent heat buildup.
Coolant and Heat Management
Proper heat management is critical when machining PA6 Mineral40. The material has relatively low thermal conductivity, so heat generated during cutting can accumulate in the workpiece, leading to dimensional changes and surface degradation. Using coolant or compressed air to remove heat is essential, particularly for finishing operations where tight tolerances are required. Flood coolant is generally preferred for production machining, while mist or air blast can be sufficient for light finishing cuts. The material’s low warpage characteristics help maintain accuracy even when heat is generated during machining, but minimizing thermal input remains a best practice.
Afwerking en nabehandeling
PA6 Mineral40 responds well to finishing operations, producing smooth surfaces with Ra values below 0.8 µm when properly machined. The material can be polished, painted, or laser-marked without difficulty. For applications requiring moisture resistance, components can be sealed with appropriate coatings. Annealing is sometimes performed after machining to relieve residual stresses and improve dimensional stability, particularly for parts that will experience elevated service temperatures. This involves heating the component to 150-170°C for 2-4 hours followed by slow cooling.
Design Considerations for PA6 Mineral40 Parts
Designing components from PA6 Mineral40 requires consideration of the material’s specific characteristics, including moisture absorption, thermal expansion, and mechanical properties. Proper design ensures optimal performance and manufacturability.
Toleranties en dimensionale stabiliteit
PA6 Mineral40 can hold tighter tolerances than unfilled nylon, with typical machining tolerances of ±0.05 mm achievable on CNC equipment. However, designers must account for the material’s moisture absorption, which can cause dimensional changes of 0.2-0.5% between dry-as-molded and moisture-saturated states. This is particularly important for precision components like precision CNC camera parts, where even small dimensional changes can affect optical alignment. Components should be designed with appropriate clearances and tolerances that accommodate this moisture-induced expansion.
Wanddikte en ribontwerp
For injection-molded PA6 Mineral40 components, uniform wall thickness is essential to prevent sink marks and internal voids. Recommended wall thickness ranges from 1.5 to 4.0 mm, with transitions between thick and thin sections kept gradual. Ribs should be 50-70% of the nominal wall thickness to avoid sink marks on visible surfaces. The material’s high stiffness allows for thinner walls than unfilled nylon, providing opportunities for weight reduction. For machined components, minimum wall thickness is typically 1.0-1.5 mm depending on part size and complexity.
Verbindings- en assemblagemethoden
PA6 Mineral40 can be joined using mechanical fasteners, ultrasonic welding, adhesive bonding, or press-fit connections. Self-tapping screws work well with the material, though thread-forming screws are preferred over thread-cutting types to avoid stress concentrations. For press-fit assemblies, the material’s creep resistance helps maintain interference fit over time. Ultrasonic welding is effective for joining PA6 Mineral40 components, producing strong, hermetic seals. When adhesive bonding, surface preparation such as corona treatment or plasma treatment is recommended to improve adhesion strength.
Tuofa CNC: Precision Machining of PA6 Mineral40
Tuofa CNC Germany specializes in precision CNC machining of engineering plastics, including PA6 Mineral40. With state-of-the-art equipment and extensive experience in polymer machining, Tuofa delivers components that meet the most demanding specifications for dimensional accuracy and surface finish.
Geavanceerde bewerkingsmogelijkheden
Tuofa CNC operates a fleet of high-precision CNC milling, turning, and drilling centers capable of machining PA6 Mineral40 to tolerances as tight as ±0.01 mm. Our machining centers are equipped with high-pressure coolant systems that effectively manage heat during cutting operations, ensuring dimensional stability and preventing thermal damage to the workpiece. We utilize specialized tooling geometries optimized for polymer machining, including polished-flute end mills and specially ground drills that produce clean, burr-free holes. This technical expertise ensures that every component meets the highest quality standards.
Kwaliteitsborging en ondersteuning
Every PA6 Mineral40 component machined by Tuofa CNC undergoes rigorous quality inspection, including dimensional verification using coordinate measuring machines (CMM) and surface finish analysis. We provide comprehensive documentation, including material certifications and inspection reports, to support your quality management system. Our engineering team offers design-for-manufacturability guidance, helping you optimize your component designs for cost-effective production. Whether you need a single prototype or large production runs, Tuofa CNC Germany delivers reliable, high-quality machined parts with competitive lead times.
Conclusion
PA6 Mineral40 is a versatile engineering thermoplastic that offers an excellent balance of mechanical strength, dimensional stability, and cost-effectiveness. Its unique combination of properties makes it suitable for a wide range of applications across automotive, electrical, and industrial sectors. The material’s excellent machinability, combined with its low warpage and good surface finish, positions it as a preferred choice for precision components. When selecting PA6 Mineral40 for your project, consider its thermal and moisture-related behavior, and partner with an experienced machining provider like Tuofa CNC to ensure optimal results. With proper design and processing, PA6 Mineral40 delivers reliable, long-lasting performance in demanding applications.